The JD 320 Skid Steer is one of the most versatile pieces of hardware that we rent. Before you rent, it is important to know the specs of your machine. With that in mind, we have put together all the specifications and features of the JD 320 Skid Steer in this blog post, giving you all the vital info before you rent. Already made your mind up? Visit our JD 320 Skid Steer reservation page to reserve yours today.
A) Length minus bucket: 8 ft. 6 in.
B) Length with bucket: 10 ft. 6 in.
C) Width minus bucket: 5 ft. 10 in.
D) Height to top of ROPS: 6 ft. 5 in.
E) Height to hinge pin: 9 ft. 7 in.
F) Dump height: 7 ft. 6 in.
G) Dump reach (foundry bucket): 28.1 in.
H) Wheelbase: 42.3 in.
I) Ground clearance: 9.6 in.
J) Angle of departure: 27 deg.
K) Front turn radius: 6 ft. 7 in.
L) Dump angle: 45 deg.
M) Bucket rollback: 35 deg.
|Model and manufacturer||John Deere PowerTech 4024T|
|Horsepower||62 net/ 66 gross|
|Non-road emission standards||Certified to EPA Tier 2 emissions|
|Rated engine speed||2,800 rpm|
|Air cleaner||Dry dual element|
|Standard pump flow||19 gpm|
|Total pump flow with high-flow option||31 gpm|
|System pressure at couplers||3,450 psi|
|Hydraulic horsepower (standard flow)||38 hp|
|Hydraulic horsepower ( high flow)||61 hp|
|Battery capacity||12 volt, 750 CCA|
|Alternator rating||12 volt, 70 amp|
|Base machine||6,435 lb.|
|System high-pressure relief||5,000 psi|
|Single-speed travel speeds||0 to 6.8 mph|
a) Park the JD 320 Skid Steer loader safely.
b) Sitting in the operator’s chair, buckle seatbelt and engage the parking brake.
c) Start the engine.
d) Run engine at maximum speed.
e) Release park brake to the run position.
f) Push down on the boom control pedal and raise the boom slowly. Release pedal and push down on the bucket control pedal to slowly curl the bucket. Release pedal.
g) Unbuckle seatbelt.
a) Park machine safely.
b) Lift latch handles to the unlatched position. Be sure all lock pins are fully extracted.
c) Enter the JD 320, fasten seat belt, start the engine and disengage the parking brake.
d) Tilt mounting plates forward.
e) Drive forward, raise the boom and guide the mounting plate under the attachment mounting brackets.
f) Raise the mounting brakes and roll them back. The back of the attachment should be touching the front of the mounting plate.
g) When the attachment is properly supported, lower the boom until it is resting on the boom stops.
h) Roll the attachment out and stop when the bottom of the attachment is 2 in. from the ground.
i) Engage parking brake, turn of the engine and exit the JD 320 skid steer.
a) Park machine safely
b) Disconnect hydraulic hoses from attachment
c) Pull the latch handles to the unlatched position and release the pins from the lower attachment tabs.
d) Enter the JD 320, start engine and disengage parking brake.
e) Lower attachment until it is safely on the ground.
f) Tilt mounting plate forward and reverse at the same time.
Want to book the JD 320 Skid Steer for your next job? Visit our JD 320 Skid Steer reservation page to reserve yours today.
Monday - Friday: 6:30AM-5:00PM
Copyright © 2022 Aspen Rent-All
site by Volatile